Single hung
Double hung
Horizontal roller
Casement
Bay & bow
Sliding glass doors
Entry doors
Impact garage doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimateTherma-Tru Door Installation in Boulder City: What to Know First
We install and replace Therma-Tru entry doors, French and double doors, storm doors, and hurricane-rated exterior doors for homeowners across Boulder City. A standard entry door swap runs one visit and a full day for our crew; French and double doors or any opening that needs framing work often take two. On price, we quote the honest number on paper before we start, and we register both warranty layers before we leave the driveway.
This page is for the homeowner who already owns a Therma-Tru door or has one picked out and wants it set right the first time. As an independent Therma-Tru service provider, TruePane Windows & Doors Boulder City is not affiliated with or authorized by Therma-Tru, but we install their lines the way the manufacturer’s own instructions require.
Call (844) 560-0350 for a free estimate. A live person answers, day or night.
How Therma-Tru Products Fail – and How We Fix Them
Therma-Tru builds a good door. What goes wrong in Boulder City is almost never the slab itself. It is how the door was hung, sealed, and finished, plus the desert swing between dry heat and monsoon humidity that works on every seam. Here are the failure modes we see most often, and what we do about each.
- Sagging and binding on Fiber-Classic and Smooth-Star entry doors. A door that catches on the strike side in July and swings free in January is usually an install where the jamb was not plumb, not a bad slab. In Boulder City’s dry summer heat, a jamb set out of plumb moves against the hinge side and the door drags. We re-check plumb and level at the hinge jamb and the head before anything gets screwed off, and we shim to true rather than forcing the slab.
- Threshold leaks on the Classic-Craft line. Therma-Tru’s adjustable sill is a good system, but installers who set it flat on a slab without the correct sill pan or a positive slope to the exterior get water tracking under the door during a hard monsoon rain. The finish cap looks fine and the subfloor gets wet. We set the sill with the right pan and a real outward slope, and we test with a hose before we call it done.
- Weathered seals on Fiber-Classic and Smooth-Star doors facing west. The polyurethane foam core holds up, but the compression weatherstrip and the door sweep dry out and crack after years of direct afternoon sun. That shows up as daylight under the door and dust blowing in. We replace the OEM sweep and weatherstrip with manufacturer-matched parts so the frame and the seal still fit as designed.
- Delamination and finish failure on steel and Fiber-Classic slabs. A door finished on one side and left bare on the other will take on moisture at the edges, and the bottom rail is where it shows first. We finish all six sides of the slab per Therma-Tru’s instructions, top and bottom rails included, before the door goes back on the hinges.
- Warped or twisted slabs on French and double-door sets. A double door that will not meet in the middle usually has one leaf installed out of square, or an astragal that was never aligned to the active leaf. We check the pair as a unit, set the astragal to the active leaf, and adjust so both leaves close to the same reveal top and bottom. If the slab itself is twisted beyond what adjustment can fix, we tell you that plainly instead of shimming around it.
Styles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
Our Therma-Tru Door Installation Process
Every Therma-Tru job follows the same sequence, whether it is a single entry door or a French pair. No surprises on the bill, and no second appointment left hanging.
- 1
Measure and diagnose. We measure the opening twice and check the existing frame for plumb, level, and square. We note the model line, the handedness, and whether the current door was ever finished on all six sides.
- 2
Quote on paper, side by side. You see the Therma-Tru line quoted against comparable options from other manufacturers we install, so you know exactly what you are buying. We tell you which parts need to be OEM to keep the warranty intact and where a quality aftermarket part is a fair substitute.
- 3
Remove and prep. Out comes the old door and frame. We inspect the rough opening for rot, check the sill pan, and correct the slope to the exterior before anything new goes in.
- 4
Set and seal. New door set plumb, level, and square with the correct flashing and sealant. We use the manufacturer’s fastening schedule, not a guess.
- 5
Test and finish. We open and close the door through its full swing, check the latch and deadbolt alignment, test for daylight and air gaps, and finish the slab on all six sides.
- 6
Register and clean up. Both manufacturer warranty layers get registered in writing, with the durations stated, before we leave. Then we clean the site and walk you through the door.
See the difference
Before
After
Before
After
Before
AfterWhat Therma-Tru Door Installation Costs in Boulder City
Prices below are typical for Boulder City homes and reflect the local market, not a national average. Every job gets a written line-item quote before work begins.
| Scenario | Typical range |
|---|---|
| Standard Therma-Tru entry door, like-for-like replacement, existing frame sound | $650 – $1,400 |
| Entry door with new frame and sill pan, rot repair at the rough opening | $1,200 – $2,600 |
| French or double door set, both leaves | $1,800 – $4,200 |
| Storm and exterior door installation | $450 – $1,100 |
| Hurricane-rated entry door | $1,400 – $3,400 |
What moves the number: door line and size, whether the rough opening needs framing or rot repair, hardware upgrades, and finish work. Call (844) 560-0350 for an exact quote. Estimates are free, and ours come in writing.
Why Boulder City Homeowners Call TruePane Windows & Doors Boulder City for Therma-Tru Work
We have proudly served local communities for over 42 years, founded by second-generation glazier Dale Kessler on the rule that still governs every job: if the pane is not true, the job is not done. Our technicians have up to 18 years of experience, they are background-checked and uniformed, and they measure every opening twice. Every job carries our 90-Day Done Right Promise and The Keystone Standard: both manufacturer warranty layers registered in writing, durations stated, before the truck leaves the driveway. If something is not done right, we make it right, no paperwork and no arguing.
A live person answers every call, 24 hours a day, 7 days a week. We also install and service PGT, CGI, CWS, and ES Windows for homeowners weighing their options. Call (844) 560-0350 for a free estimate.
FAQs
No, not when the door is installed to Therma-Tru’s written instructions and the warranty is registered. We follow the manufacturer’s fastening and finishing schedule, and we register both warranty layers in writing before we leave. That is The Keystone Standard on every job.
Common Therma-Tru parts like sweeps, weatherstrip, and sill components are available through supplier channels, and most arrive within a normal lead time from order. We tell you at quote time which parts are OEM and which lead times apply, so nothing surprises you mid-job. Call (844) 560-0350 for a parts check on your model.
Repair usually wins when the slab is sound and the problem is the frame, seal, or hardware. Replace when the slab is warped, delaminated, or the rough opening has rot. We measure twice and tell you honestly which one you are facing, then quote both if there is any question.
A standard entry door swap is a single visit and one full day. French and double doors, or any opening that needs framing work, typically take two visits. Most jobs are completed in a single visit, and we tell you the schedule up front.
Not if it is not in the written quote. We quote line-item, on paper, before we start. If we open the wall and find rot that was not visible at the estimate, we stop and tell you before we add a line, so there are no surprise charges on the bill.
Call (844) 560-0350 to schedule your free estimate. A live person answers around the clock, and we will tell you plainly what your Therma-Tru door needs and what it will cost.
Written by the team at TruePane Windows & Doors Boulder City, serving Boulder City and nearby areas.