Single hung
Double hung
Horizontal roller
Casement
Bay & bow
Sliding glass doors
Entry doors
Impact garage doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimatePGT Door Installation in Boulder City: What to Know First
We install PGT doors in Boulder City as an independent PGT service provider. Most standalone door replacements are completed in a single visit; jobs that involve a wider opening or a change in door style usually take two. Expect honest, upfront pricing before we touch a hinge, and a written line-item quote, not a number scribbled on the back of a business card.
This page is for the homeowner who already has PGT windows or doors in the house, or who has settled on PGT as the line they want, and now needs the door set right. That means reading the opening, matching the door to the frame you actually have, and registering both warranty layers before we leave the driveway. If you have a PGT door on order or a PGT door that is not sitting true, call us at (844) 560-0350 and we will talk through it.
How PGT Products Fail – and How We Fix Them
PGT builds a solid product, and most of what we see in Boulder City is not a manufacturing problem. It is an installation or adjustment problem that shows up years later. Here are the failure modes we run into on PGT doors, named to the line where we can.
- PGT Aluminum Series entry doors that drag at the strike side in July. Boulder City heat pushes the aluminum frame and the slab at different rates, and a door hung with too little reveal clearance will bind against the jamb once the afternoon sun hits it. The homeowner blames the door. The real cause is the installation set the gap too tight for this climate. We reset the frame with the reveal the door needs and true the strike so it latches without a shoulder into it.
- Hurricane-rated PGT doors with water showing up at the threshold after a monsoon. PGT impact doors are rated for wind-borne debris and pressure, but the rating only holds if the threshold is bedded and flashed correctly. We see sill pans skipped on retrofits. Our fix is to pull the door, re-bed the sill with the flashing the rating calls for, and verify the water path sheds away from the house, not into the wall cavity.
- PGT French and double doors where the inactive leaf sags and the astragal stops meeting. Nine times out of ten the hinge screws have worked loose in the jamb because the jamb was shimmed only at the hinges and not between them. We re-shim the full jamb, replace the short screws with the length the jamb needs, and re-hang the leaves so the meeting stile closes clean.
- PGT storm and exterior doors with a fogged or leaking glass unit. The insulated glass seal fails, moisture creeps in, and the unit fogs from the bottom edge up. That is a glass replacement, not a door replacement, and it is worth doing correctly because the door frame is usually fine. We measure the unit to the manufacturer’s spec and order the OEM glaze if it is available.
- Replacement doors where the rough opening was never squared. The old door came out, a new PGT door went in, and nobody checked the opening first. A door installed into an out-of-square opening will never sit true no matter how many adjustments are made. We check the opening before the door ships and correct it if it is off.
One detail homeowners cannot get from the manufacturer’s own material: the PGT door line you own determines the parts path. Standard aluminum entry doors have broad aftermarket hinge and closer support, but the impact-rated lines and the custom configurations often need OEM hardware to keep the rating and the warranty intact. On PGT work we always price the OEM part against a quality aftermarket equivalent and show you both on paper. You decide. We do not swap a rated part for a cheaper one without telling you what it does to your coverage.
Styles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
Our PGT Door Installation Process
- 1
The call and the measure. You call, a live person answers, and we set a time. On site we measure the opening twice, check it for square and plumb, and write down the door line, the series, and the existing hardware.
- 2
The quote, on paper. We quote the PGT door and any alternative lines side by side so you can see exactly what you are buying. Upfront pricing, no surprise line items later.
- 3
The parts decision. OEM versus quality aftermarket, priced both ways, with the warranty consequence spelled out. No hidden swaps.
- 4
The install. Old door out, opening corrected if it needs it, new PGT door set, shimmed full-height, flashed and bedded at the sill, hardware hung and adjusted.
- 5
The test. We open and close the door through its full swing, check the latch and the lock, and verify the reveal is even top to bottom and side to side before we call it done.
- 6
The registration and cleanup. Both manufacturer warranty layers registered in writing with the durations stated, then the site swept and the old door hauled away. All under our 90-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterWhat PGT Door Installation Costs in Boulder City
Door pricing in Boulder City runs a little higher than the flatland averages because the heat and the wind load both push toward heavier-rated products. Here is what common PGT scenarios run:
| Scenario | Typical range |
|---|---|
| PGT entry door replacement, standard aluminum, single door | $1,400 – $3,200 |
| Hurricane-rated PGT impact entry door | $2,600 – $5,800 |
| PGT French or double door set | $3,200 – $7,500 |
| PGT storm or exterior door replacement | $1,200 – $2,800 |
| Insulated glass unit replacement in an existing PGT door | $350 – $850 |
| Frame correction for an out-of-square opening | $400 – $1,200 |
What moves the number: the door series, impact versus non-impact rating, whether the opening is square, and whether the hardware is OEM. Existing customers can use $50 Off Any Repair Over $250, our $89 Seasonal Tune-Up, and a permanent 5% discount for seniors and veterans. Call (844) 560-0350 for a free estimate; we will put the number in writing.
Why Boulder City Homeowners Call TruePane Windows & Doors Boulder City for PGT Work
PGT is one of more than a dozen manufacturer lines we install, alongside Andersen, Pella, Marvin, Milgard, Jeld-Wen, CGI, and ES Windows. That matters because when a PGT part is on backorder, we can still get the job done and tell you honestly whether a different line would serve you better. Our technicians have up to 18 years of experience and measure every opening twice.
Every job carries our 90-Day Done Right Promise and The Keystone Standard: both warranty layers registered in writing before we leave. If it is not done right, we make it right, no paperwork fight. We are a second-generation glazier’s shop, and we plan to be in Boulder City in thirty years. That is why we hire local, train our apprentices into journeymen, and answer the phone with a live person around the clock. If your PGT door is not sitting true, we would like to be the last call you have to make.
FAQs
Does installing a PGT door through TruePane affect my PGT warranty? Not when it is installed to PGT’s written specification, and that is exactly how we do it. We are an independent PGT service provider, not affiliated with PGT, and we register both manufacturer warranty layers in writing before we leave so your coverage is on record.
Can you get PGT replacement parts for a door in Boulder City? Yes for most lines. Standard aluminum entry door hardware has broad availability; the impact-rated and custom configurations sometimes need OEM parts and a lead time. We quote the OEM part and a quality aftermarket equivalent side by side and tell you what each one does to your warranty. Call (844) 560-0350 for an exact quote on parts, free.
Should I repair my PGT door or replace it? If the frame and glass are sound and the problem is a hinge, a sill, or an adjustment, repair is usually the right call and far cheaper. If the door is out of square in the opening, or the glass seals have failed on an older unit and the door is not otherwise in good shape, replacement makes more sense. We will tell you which one honestly after we look.
How long does a PGT door installation take? A standard single entry door is usually done in a single visit. French doors and double door sets, or jobs that need the opening corrected, take longer and sometimes a second visit. We tell you the schedule before we start and we show up when we say.
Do you handle other brands besides PGT? Yes. We install and service PGT as well as CGI, CWS, ES Windows, and ECO Window Systems, plus Andersen, Pella, Marvin, Milgard, and Jeld-Wen. If a PGT part is slow to arrive, we have somewhere to go.
If your PGT door is binding, leaking, or fogged, or you have a new one that needs setting right, call TruePane Windows & Doors Boulder City at (844) 560-0350 for a free estimate. Upfront pricing, both warranty layers registered in writing, and a 90-Day Done Right Promise on the work. If the pane is not true, the job is not done.
Written by the team at TruePane Windows & Doors Boulder City, serving Boulder City and nearby areas.