Impact garage doors
Single hung
Double hung
Horizontal roller
Casement
Bay & bow
Sliding glass doors
Entry doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimateCGI Impact Garage Doors: The Boulder City Owner’s Guide
We install CGI impact garage doors and their supporting hardware for Boulder City homeowners, and a full impact door replacement typically runs $3,200 to $6,800 installed, depending on door width, glazing package, and whether the opening needs track and spring work. Parts-only jobs like rollers, hinges, and weather seals usually land between $180 and $520 installed. Impact doors are a planned install, not an emergency callout, so we schedule them properly rather than promising same-day turnaround.
Owners here usually find out something is wrong the same way every time. The door gets heavy on the last foot of travel. The opener strains and the light flickers. Or a panel edge starts to show spider-web cracking after a monsoon-season wind event, and the hardware that holds it in the track begins to give. Boulder City sits in a high-wind, high-heat corridor, and impact-rated doors carry heavier panels than standard ones, which puts more load on the springs, cables, and hinges than most homeowners expect.
Key Takeaways
- CGI impact doors use heavier panels than non-impact doors, so springs, cables, and rollers wear faster and fail earlier.
- Match the part to your exact CGI model and label – the wrong spring or hinge is a real safety problem, not a minor fit issue.
- Full impact door replacement in Boulder City typically runs $3,200 to $6,800 installed; component repairs run $180 to $520.
- Springs and cables are the one part of this system you should never touch yourself. Call us instead.
- A live person answers (844) 560-0350 any hour, and estimates are free.
Which CGI Models This Applies To
CGI makes a range of impact-rated residential garage doors under its hurricane and impact lines, and the parts do not cross over cleanly between them. Before you order anything, find the model label. On most CGI doors it’s a sticker on the inside face of the top or bottom panel, or a metal tag on the end stile, and it lists the model number, panel thickness, and wind-load rating. That label is what tells us which torsion spring wire gauge and which hinge gauge your door actually needs. A door rated for a higher design pressure carries a heavier panel, which means a heavier spring. Guess wrong on that spring and you’ve created a door that either won’t balance or slams shut under load.
Then there’s the OEM question. CGI-branded replacement springs, hinges, and rollers are the safest match and the ones we prefer to quote first. Quality aftermarket equivalents exist and are often available faster, and for wear items like nylon rollers and bottom seals they hold up well. For torsion springs and lift cables on an impact door, we lean toward OEM or a documented equivalent with the correct cycle rating. Boulder City’s heat is hard on spring steel, and an under-rated spring will fatigue fast regardless of who made it. We’re an independent service provider and not affiliated with CGI, which means we’re free to quote both sides honestly and let you see the difference on paper.
Styles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
Signs Your CGI Impact Garage Doors Are Failing
- The door feels heavy when you lift it by hand. A balanced door should lift with light effort and stay put halfway up. Heaviness on the way up usually means a torsion spring has lost tension or a cable has slipped a drum. That’s a spring-and-cable problem, and it’s the one item on this list you should not try to fix yourself.
- The opener strains, or the door reverses for no reason. Impact panels are heavier than standard ones, and when the springs weaken the opener picks up the slack. It runs hot, trips its force limit, and starts reversing. The opener is usually fine; the springs are telling you they’re done.
- You see cracked or crazed glazing at the panel edge. Impact glazing is laminated, and when it starts to fail it shows as spider-webbing or a white haze along the frame. That’s a glazing failure, and on a CGI impact door it means the panel needs service, not a patch.
- The door binds, scrapes, or jumps in the track. Worn rollers and bent hinges let the door cock sideways in the track. In Boulder City’s heat, nylon rollers flat-spot and steel hinges loosen at the screws. Left alone, a binding door will eventually pull a hinge out of the panel.
- Daylight or dust showing around the edges. Worn bottom seals and perimeter weatherstrip let wind-driven dust and heat inside. Cheap part, but it lets conditioned air out and grit into your tracks.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what CGI impact garage door work runs in Boulder City, with parts and labor quoted together so there are no surprise line items on the bill. These are installed prices, not parts-only figures.
| Job | Typical Installed Range |
|---|---|
| Full impact door replacement (single-car) | $3,200 – $5,200 |
| Full impact door replacement (double-car) | $4,600 – $6,800 |
| Torsion spring replacement (pair) | $320 – $520 |
| Cable replacement and drum re-set | $240 – $420 |
| Roller and hinge service (full door) | $180 – $340 |
| Bottom seal and weatherstrip | $180 – $290 |
What drives the range is mostly door size, glazing package, and whether the opening needs new tracks or a re-set. We quote manufacturer lines side by side on paper so you see exactly what you’re buying, and every job is covered by the 90-Day Done Right Promise with both warranty layers registered in writing before we leave. If it’s not done right, we make it right – no paperwork fights.
DIY or Call Us?
Some of this is safe to check yourself, and some of it can put you in the hospital. Here’s the honest split.
Safe to check: whether the door feels heavy when you lift it by hand, whether rollers are flat-spotted or cracked, whether the bottom seal is torn, and whether the model label is legible. You can also read your panel for cracking and snug down a loose hinge screw with a screwdriver. That’s it.
Do not touch the torsion springs or the lift cables. Those parts are under extreme tension, and a spring or cable that lets go can cause serious injury. This is not a scare tactic – it’s the single most common way homeowners get hurt doing garage door work. Replacing a torsion spring on an impact door also takes the correct wire gauge, a winding bar, and the right number of turns to balance the heavier panel, and getting it wrong means a door that slams shut. Springs are the one part where calling a trained technician isn’t optional.
Call (844) 560-0350 and a live person picks up any hour. Free estimates, upfront pricing, and background-checked technicians who answer the phone the way they show up – on time and prepared.
FAQs
Plan on roughly 7 to 12 years for torsion springs on an impact door here, and up to 20 to 25 years for the door panels themselves with normal care. Boulder City’s heat and the heavier impact panels both shorten spring life compared to milder climates, so we see more spring failures in this town than owners expect. Call (844) 560-0350 for an exact quote – estimates are free.
Often yes, and we’ll tell you which way makes sense. Rollers, hinges, seals, and cables are almost always repair jobs; a tired torsion spring can sometimes be re-tensioned rather than replaced if the wire is still sound. A cracked glazing panel or a structurally compromised door is usually a replacement. We quote both so you can decide. Call (844) 560-0350 and we’ll walk you through it.
A component job like a spring pair, cables, or roller service is typically done in a single visit, often in two to three hours. A full impact door replacement is a scheduled install, usually a full day, and we come prepared to finish it in one visit. We’ll be there when we say, and we’ll tell you the real window up front.
We match the part to your exact CGI model label and quote OEM and documented aftermarket equivalents side by side on paper. As an authorized installer for more than a dozen manufacturer lines, including CGI, we can order the right part the first time rather than guessing at the gauge and fit. Call (844) 560-0350 to get started.
When your CGI impact garage door needs a part or a whole door, you shouldn’t have to chase down a phone tree or wait for a callback. Call us at (844) 560-0350 for a free estimate. A live person answers 24 hours a day, 7 days a week. We’ll quote it straight, register both warranty layers in writing, and stand behind the work with the 90-Day Done Right Promise. The founding rule still holds: if the pane is not true, the job is not done. Right now we’re also running $50 Off Any Repair Over $250, an $89 Seasonal Tune-Up, and a standing 5% discount for seniors and veterans.
Written by the team at TruePane Windows & Doors Boulder City, serving Boulder City and nearby areas.